10G BiDi SFP+ 60km Optical Transceiver
Matched 10G BiDi SFP+ pair for single-fiber links up to 60km over SMF, using complementary 1270nm / 1330nm directions, Simplex LC and DDM / DOM.
Specifications
- Warranty
- 3-Years
- Customization
- Free OEM labeling
- Delivery Time
- 48 hours dispatch
1. Confirm the single-fiber link conditions first.
The Axonode 10G BiDi SFP+ 60km solution uses two complementary modules over one single-mode fiber strand. Confirm the route, connector type and patching arrangement, total optical loss and compatibility coding before deployment.
10G SFP+ Port
Confirm a standard 10G SFP+ port and required coding.
Simplex LC / Single Fiber
Use one SMF strand with Simplex LC.
Reach Up to 60km
Verify route loss and engineering margin.
2. Matched modules and optical specifications
Module A uses TX 1270nm / RX 1330nm. Module B uses TX 1330nm / RX 1270nm. The two directions must be complementary.
| Product Type | 10G BiDi SFP+ Pair |
| Pair Part Number | A-10G-BIDI-60KM |
| Module A | A-10G-BIDI-60-1270 - TX 1270nm / RX 1330nm |
| Module B | A-10G-BIDI-60-1330 - TX 1330nm / RX 1270nm |
| Data Rate | Up to 10.7Gbps; 10.3125Gbps supported |
| Reach / Interface | 60km over SMF / Simplex LC |
| Wavelength Ranges | 1260-1280nm and 1320-1340nm |
| TX Power | +1 to +6dBm |
| Receiver Sensitivity | -20dBm maximum |
| Receiver Overload | -6dBm |
| Extinction Ratio / SMSR | 3.5dB minimum / 30dB minimum |
| Power | 3.3V; 3.135-3.465V; 450mA maximum |
| DDM / DOM | Supported |
| Temperature Options | 0 to +70 C; -20 to +80 C; -40 to +85 C |
| Compliance | SFP+ MSA, SFF-8472 and RoHS |
3. Long-reach single-fiber deployment
This matched pair is intended for fiber-constrained metro, ISP backhaul and regional point-to-point links. Confirm the complete loss budget and received power at both ends.
4. Compatibility prepared for your network
Confirm the exact host model, software or firmware, port mode, coding and required module direction. SFP+ form factor alone does not guarantee acceptance.
5. Testing and compliance
Testing can include wavelength direction, optical power, DDM readings, host recognition and link establishment according to product and project requirements.
Frequently Asked Questions
i. How are the modules paired?
Use TX 1270nm / RX 1330nm at one end and TX 1330nm / RX 1270nm at the other.
ii. Does the link use one fiber?
Yes. It uses one SMF strand with Simplex LC connections.
iii. Is 60km guaranteed on every route?
No. Confirm route loss, connectors, splices and engineering margin against the optical limits.
iv. Can identical directions be linked?
No. The directions must be complementary.
v. What should be checked before ordering?
Confirm host models, coding, reach, fiber route, loss budget and required A/B quantities.
vi. Can it be used on a short low-loss link?
Check received power against the -6dBm overload limit and add attenuation when engineering calculations require it.
vii. What should be checked if the link fails?
Check wavelength pairing, coding, port configuration, LC cleanliness, continuity and DDM readings.
viii. Is compatibility universal?
No. Host coding and software requirements must be verified for the target equipment.
Downloads
Request the 10G BiDi 60km datasheet
Confirm your 10G BiDi pair
Share the device models, link loss, fiber route and required quantities.
Request Compatibility Check
